EI、Scopus 收录
中文核心期刊
Li Nian, Chen Puhui. CONTINUUM DAMAGE MECHANICS MODEL FOR LOW-VELOCITY IMPACT DAMAGE ANALYSIS OF COMPOSITE LAMINATES[J]. Chinese Journal of Theoretical and Applied Mechanics, 2015, 47(3): 458-470. DOI: 10.6052/0459-1879-14-169
Citation: Li Nian, Chen Puhui. CONTINUUM DAMAGE MECHANICS MODEL FOR LOW-VELOCITY IMPACT DAMAGE ANALYSIS OF COMPOSITE LAMINATES[J]. Chinese Journal of Theoretical and Applied Mechanics, 2015, 47(3): 458-470. DOI: 10.6052/0459-1879-14-169

CONTINUUM DAMAGE MECHANICS MODEL FOR LOW-VELOCITY IMPACT DAMAGE ANALYSIS OF COMPOSITE LAMINATES

Funds: The project was supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
  • Received Date: June 08, 2014
  • Revised Date: April 19, 2015
  • A three-dimensional anisotropic continuum damage mechanics (CDM) model, including damage characterization, damage initiation criterion and damage evolution law, was presented to analyze low-velocity impact damage of composite laminates. With considering affects of the fracture plane angle, material constitutive relation of damage states in the fracture plane coordinates was established by introducing damage state variable matrix in the material principal coordinates. The onset of damage was evaluated by the Puck criterion and the evolution of damage was controlled by equivalent strain on the fracture plane. Based on the viewpoint of strain energy release, the material was assumed to exhibit linear strain-softening behavior. Fiber fracture (FF) and inter-fiber fracture (IFF) were simulated within the lamina. Due to the experimental evidence which indicated that multiple intralaminar cracks developed in a composite laminate and coalesced in to one interface crack (delamination) under impact load, a intralaminar matrix crack density parameter at saturation was introduced to scale interlaminar delamination. The relevant low velocity damage response parameters of the laminates [03/45/-45]S and [45/0/-45/90]4S were predicted with the proposed model at various impact energies. A good agreement was achieved with experimentally obtained data and showed the validity of CDM model in this paper. Furthermore, results for different mesh-densities indicated that the approach by introducing a characteristic length of the element could alleviate the mesh dependency at the stage of material damage evolution.
  • 沈真, 刘峰. 新的韧性复合材料评定技术, 623S-200101-114, 中国飞机强度研究所, 2001 (Shen Zhen, Liu Feng. New toughness composite evaluation technology,623S-200101-114, Aircraft Strength Institute of China, 2001 (in Chinese))
    陈普会, 沈真, 聂宏. 复合材料层压板冲击后压缩剩余强度的统计分析与可靠性评估. 航空学报, 2004, 25(6): 573-576 (Chen Puhui, Shen Zhen, Nie Hong. Statistical analysis of post impact compression strength of a composite laminate and reliability evaluation. Acta Aeronautica et Astronautica Sinica, 2004, 25(6): 573-576 (in Chinese))
    Bouvet C, Castanie B, Bizeul M, et al. Low velocity impact modelling in laminate composite panels with discrete interface elements. International Journal of Solids and Structures, 2009, 46: 2809-2821
    Davila CG, Camanho PP, Rose CA. Failure criteria for FRP laminates. Journal of Composite Materials, 2005, 39(4): 323-345
    Petit S, Bouvet C, Bergerot A, et al. Impact and compression after impact experimental study of a composite laminate with a cork thermal shield. Composite Science and Technology, 2007, 67: 3286-3299
    Puck A, Schurmann H. Failure analysis of FRP laminates by means of physically based phenomenological models. Composite Science and Technology, 1998, 58(10): 1045-1067
    Hinton MJ, Kaddour AS, Soden PD. A comparison of the predictive capabilities of current failure theories for composite laminates judged against experimental evidence. Composite Science and Technology, 2002, 62: 1725-1797
    Soden PD, Kaddour AS, Hinton MJ. Recommendations for designersand researchers resulting from the world-wide failure exercise. Composite Science and Technology, 2004, 64: 589-604
    Faggiani A, Falzon BG. Predicting low-velocity impact damage on a stiffened composite panel. Composites: Part A, 2010, 41: 737-749
    Shi Y, Swait T, Soutis C. Modelling damage evolution in composite laminates subjected to low velocity impact. Composite Structures, 2012, 94: 2902-2913
    Matzenmiller A, Lubliner J, Taylor RL. A constitutive model for anisotropic damage in fiber composite. Mech Mater, 1995, 20(2): 125-152
    Hwang TK, Hong CS, Kim CG. Probabilistic deformation and strength prediction for a filament wound pressure vessel. Composites: Part B, 2003, 34: 481-497
    Kim EH, Rim MS, Lee I, et al. Composite damage model based on continuum damage mechanics and low velocity impact analysis of composite plates. Composite Structures, 2013, 95: 123-134
    Lopes CS, Camanho PP, Gurdal Z, et al. Low-velocity impact damage on dispersed stacking sequence laminates. Part II: Numerical simulations. Composite Science and Technology, 2009, 69(7-8): 937-947
    Falzon BG, Apruzzese P. Numerical analysis of interlaminar failure mechanisms in composite structures. Part I: FE implementation. Composite Structures, 2011, 93(2): 1039-1046
    Falzon B G, Apruzzese P. Numerical analysis of interlaminar failure mechanisms in composite syructures. Part II: Applications. Composite Structures, 2011, 93(2): 1047-1053
    姚辽军, 赵美英, 万小朋. 基于CDM-CZM的复合材料补片补强参数分析. 航空学报, 2012, 33(4): 666-671 (Yao Liaojun, Zhao Meiying, Wan Xiaopeng. Parameter analysis of composite laminates with patched reinforcement Based on CDM-CZM. Acta Aeronautica et Astronautica Sinica, 2012, 33(4): 666-671 (in Chinese))
    Linde P, Pleitner J, de Boer H, et al. Modelling and simulation of fibre metal laminates. ABAQUS Users Conference, Boston, Dassault Systemes Company, 2004: 421-439
    吴义韬, 姚卫星, 吴富强. 基于应变能耗散的复合材料层合板面内缺口强度分析CDM模型. 复合材料学报, 2014, 31(4): 1013-1021 (Wu Yitao, Yao Weixing, Wu Fuqiang. Energy-based CDM model for analyzing intralaminar strength of notched composite laminates. Acta Materiae Compositae Sinica, 2014, 31(4): 1013-1021 (in Chinese))
    Caprino G. Residual strength prediction of impacted CFRP laminates. Journal of Composite Materials, 1984, 18: 508-518
    朱炜垚, 许希武. 复合材料层合板低速冲击损伤的有限元模拟. 复合材料学报, 2010, 27(6): 200-207 (Zhu Weiyao, Xu Xiwu. Finite element simulation of low velocity impact damage on composite laminates. Acta Materiae Compositae Sinica, 2010, 27(6): 200-207 (in Chinese))
    Aymerich F, Dore F, Priolo P. Prediction of impact-induced delamination in cross-ply composite laminates using cohesive interface elements. Composites Science and Technology, 2008, 68: 2383-2390
    Turon A, Davila CG, Camanho PP, et al. An engineering solution for mesh size effects in the simulation of delamination using cohesive zone models. Engineering Fracture Mechanics, 2007, 74(10): 1665-1682
    Donadon MV, Iannucci L, Falzon BG, et al. A progressive failure model for composite laminates subjected to low velocity impact damage. Composite and Structures, 2008, 86: 1232-1252
    屈天骄, 郑锡涛, 范献银. 复合材料层合板低速冲击损伤影响因素分析. 航空材料学报, 2011, 31(6): 81-86 (Qu Tianjiao, Zheng Xitao, Fan Xianyin. Exploration of several influence factors of low-velocity impact damage on composite laminates. Journal of Aeronautical Materials, 2011, 31(6): 81-86 (in Chinese))
    Gonzalez EV, Maimi P, Camanho PP, et al. Effects of ply clustering in laminated composite plates under low-velocity impact loading. Composites Science and Technology, 2011, 71: 805-817
    刘新东, 郝继平. 连续介质损伤力学. 北京:国防工业出版社,2011 (Liu Xindong, Hao Jiping. Continuum Damage Mechanics. Beijing: National Defence Industry Press, 2011 (in Chinese))
    Deuschle HM. 3D failure analysis of UD fibre reinforced composites: Puck's theory within FEA. [PhD Thesis]. Germany: University Stuttgart, 2010
    Wiegand J, Petrinic N, Elliott B. An algorithm for determination of the fracture angle for the three-dimensional Puck matrix failure criterion for UD composites. Composite Science and Technology, 2008, 68: 2511-2517
    Lapczyk I, Hurtado J. A progressive damage modeling in fiber-reinforced materials. Composites Part A, 2007, 38: 2333-2341
    Mitrevski T, Marshall IH, Thomson R. The influence of impactor shape on the damage to composite laminates. Composite Structures, 2006, 76: 116-122
    Choi HY, Downs RJ, Chang FK. A new approach toward understanding damage mechanisms and mechanics of laminated composites due to low-velocity impact, part I. Journal of Composite Materials, 1991, 25(8): 992-1011
    Choi HY, Downs RJ, Chang FK. A new approach toward understanding damage mechanisms and mechanics of laminated composites due to low-velocity impact, part II. Journal of Composite Materials, 1991, 25(8): 1012-1038
    Raimondo L, Iannucci L, Robinson P, et al. A progres-sive failure model for mesh size independent FE analysis of composite laminates subject to low-velocity impact damage. Composite Science and Technology, 2012, 72: 624-632
    Gonzalez EV, Maimi P, Camanho PP, et al. Simulation of drop-weight impact and compression after impact tests on composite laminates. Composite Structures, 2012, 94: 3364-3378
    Feng D, Aymerich F. Finite element modelling of damage induced by low-velocity impact on composite laminates. Composite Structures, 2014, 108: 161-171
    王一飞, 张晓晶, 汪海. 复合材料层压板低速冲击响应与损伤参数关系研究. 固体力学学报, 2013, 34(1): 63-72 (Wang Yifei, Zhang Xiaojing, Wang Hai. Low-velocity impact response of composite laminate and its relationship with damage parameters. Chinese Journal of Solid Mechanics, 2013, 34(1): 63-72 (in Chinese))
    Nairn JA. Matrix Microcracking in Composites. Polymer Matrix Composites, 2000, 2: 403-432
    Talreja R, Singh CV. Damage and Failure of Composite Materials. Cambridge: Cambridge University Press, 2012
    Talreja R. Fatigue of Composite Materials. Lancaster, Pa: Technomic, 1987
  • Related Articles

    [1]Huang Kai, Li Mingpeng. RESEARCH ON THE STRAIN RATE DEPENDENCE OF PHASE TRANSFORMATION PATTERN EVOLUTION IN NITI ALLOYS[J]. Chinese Journal of Theoretical and Applied Mechanics, 2025, 57(5): 1-9. DOI: 10.6052/0459-1879-25-055
    [2]Meng Xufei, Bai Peng, Liu Jianxia, Chen Lili, Liu Chuanzhen. WAVERIDING DEPENDENT AREA[J]. Chinese Journal of Theoretical and Applied Mechanics, 2024, 56(6): 1644-1654. DOI: 10.6052/0459-1879-23-510
    [3]Wei Xinyu, Sang Jianbing, Zhang Ruilin, Wang Jingyuan, Liu Baoyou. TIME-DEPENDENT MECHANICAL BEHAVIOR AND CONSTITUTIVE PARAMETER IDENTIFICATION OF CHONDROCYTES BASED ON MACHINE LEARNING[J]. Chinese Journal of Theoretical and Applied Mechanics, 2022, 54(11): 3215-3222. DOI: 10.6052/0459-1879-22-344
    [4]Gan Yangke, Liu Jianfei. AUTOMATIC VISCOUS BOUNDARY LAYER MESH GENERATION[J]. Chinese Journal of Theoretical and Applied Mechanics, 2017, 49(5): 1029-1041. DOI: 10.6052/0459-1879-17-154
    [5]Yangjun Luo. Topology optimization of pressure-dependent material structures based on D-P criterion[J]. Chinese Journal of Theoretical and Applied Mechanics, 2011, 43(5): 878-885. DOI: 10.6052/0459-1879-2011-5-lxxb2011-003
    [6]Shengli Xu, Gengdong Cheng. Material design of permeability coefficient based on adaptive mesh[J]. Chinese Journal of Theoretical and Applied Mechanics, 2010, 42(2): 238-244. DOI: 10.6052/0459-1879-2010-2-2008-730
    [7]Bin Ji, Wanji Chen, Jie Zhao. Elastoplastic finite element analysis of shear band with couple stress theory[J]. Chinese Journal of Theoretical and Applied Mechanics, 2009, 41(2): 192-199. DOI: 10.6052/0459-1879-2009-2-2007-416
    [8]A universal numerical discretization method on different meshes[J]. Chinese Journal of Theoretical and Applied Mechanics, 2004, 36(4): 393-400. DOI: 10.6052/0459-1879-2004-4-2003-170
    [9]A CONSTITUTIVE MODEL FOR NONPROPORTIONAL CYCLIC PLASTICITY WITH LOADINGPATH DEPENDENCE[J]. Chinese Journal of Theoretical and Applied Mechanics, 1999, 31(4): 484-492. DOI: 10.6052/0459-1879-1999-4-1995-057
    [10]TEMPERATURE DEPENDENCE OF THE GRAIN BOUNDARY RELAXATION IN ALUMINIUM BICRYSTALS[J]. Chinese Journal of Theoretical and Applied Mechanics, 1993, 25(1): 22-28. DOI: 10.6052/0459-1879-1993-1-1995-610

Catalog

    Article Metrics

    Article views (1579) PDF downloads (1164) Cited by()
    Related

    /

    DownLoad:  Full-Size Img  PowerPoint
    Return
    Return