EI、Scopus 收录
中文核心期刊
祁晓斌, 施瑶, 刘喜燕, 潘光. 阶梯式圆柱射弹小角度入水弹道特性研究. 力学学报, 2023, 55(11): 2468-2479. DOI: 10.6052/0459-1879-23-212
引用本文: 祁晓斌, 施瑶, 刘喜燕, 潘光. 阶梯式圆柱射弹小角度入水弹道特性研究. 力学学报, 2023, 55(11): 2468-2479. DOI: 10.6052/0459-1879-23-212
Qi Xiaobin, Shi Yao, Liu Xiyan, Pan Guang. Study on trajectory characteristics of stepped cylindrical projectile entering water at small angle. Chinese Journal of Theoretical and Applied Mechanics, 2023, 55(11): 2468-2479. DOI: 10.6052/0459-1879-23-212
Citation: Qi Xiaobin, Shi Yao, Liu Xiyan, Pan Guang. Study on trajectory characteristics of stepped cylindrical projectile entering water at small angle. Chinese Journal of Theoretical and Applied Mechanics, 2023, 55(11): 2468-2479. DOI: 10.6052/0459-1879-23-212

阶梯式圆柱射弹小角度入水弹道特性研究

STUDY ON TRAJECTORY CHARACTERISTICS OF STEPPED CYLINDRICAL PROJECTILE ENTERING WATER AT SMALL ANGLE

  • 摘要: 圆锥圆柱外形射弹小角度高速入水过程中, 入水初期空泡呈不对称性发展. 随着入水角度减小, 入水空泡发展不对称性现象加剧, 使得弹体受到阶跃性突变力矩作用, 导致其姿态角发生大幅度变化, 严重影响射弹入水弹道稳定性, 甚至出现入水跳弹现象. 为了改善高速射弹小入水角度入水过程弹道稳定性, 基于“空化器空化效应”原理提出了一种阶梯式圆柱外形射弹设计方案. 通过流体体积多相流模型和动网格技术, 建立超空泡射弹小角度入水数值计算方法, 并通过入水试验验证了数值方法的有效性. 对阶梯圆柱外形射弹与圆锥圆柱外形射弹以5°入水角的入水过程进行了数值模拟研究, 得到了不同射弹外形空泡演化特性对水动力特性及弹道稳定性的影响. 结果表明: 阶梯圆柱外形能够加快初生空泡的发展并伴随多空泡融合现象, 在0°攻角条件下, 当空泡充分发展后, 空泡尺寸未发生改变, 在小攻角(5°)工况下, 空泡对弹体的包覆面积增大, 改善了射弹的升力性能; 在小角度入水过程中射弹锥段空泡发展形态对入水稳定性具有重要影响, 阶梯圆柱外形能够有效加快入水空泡的发展, 进而形成有效抑制攻角持续增大的恢复力矩, 提升了高速射弹小角度入水初期弹道稳定性.

     

    Abstract: In the process of the high speed water entry of a conical cylindrical projectile at small angle, the initial cavity develops asymmetrically. With the decrease of the water entry angle, the asymmetric phenomenon of the development of the initial cavity is intensified. As a result, the projectile body is subjected to the step abrupt moment, resulting in a large change in its attitude angle, which seriously affects the stability of the projectile's water-entering trajectory, and even the phenomenon of water-entering ricochet occurs. In order to improve the ballistic stability of high-speed projectile during small angle water entry, a stepped cylindrical projectile design scheme is proposed based on the principle of cavitation effect of cavitator. Based on fluid volume multiphase flow model and dynamic mesh technique, the numerical calculation method of the small angle water entry of the supercavitation projectile is established, and the effectiveness of the numerical method is verified by water entry experiments. By comparing the calculation results of the stepped cylindrical shape model and the conical cylindrical shape model, the influence of the cavity evolution characteristics of different projectile shapes on the hydrodynamic characteristics and ballistic stability is obtained. The results show that the shape of the stepped cylinder can accelerate the development of the primary cavity, and there is a phenomenon of multi-cavity fusion. When the angle of attack is 0°, the cavity size does not change after the cavity is fully developed. Under the condition of small angle of attack (5°), the area of the cavity-wrapped body increases, which improves the lift performance of the projectile. In the process of the water entry with small water entry angle, the development of the cavity form in the cone of the projectile has an important effect on the water entry stability. The stepped cylinder shape can effectively accelerate the development of water entry cavity, form a recovery moment to effectively restrain the continuous increase of the angle of attack, and improve the initial ballistic stability of the high-speed projectile in the small water entry angle.

     

/

返回文章
返回