旋转碰摩板热冲击振动的解析法研究

寇海江; 袁惠群; 赵天宇

doi:10.6052/0459-1879-14-075

旋转碰摩板热冲击振动的解析法研究

doi: 10.6052/0459-1879-14-075

1 东北大学机械工程与自动化学院, 沈阳 110819
2 东北大学理学院, 沈阳 110819

基金项目: 国家自然科学基金项目(51275081)和国家自然科学基金重点项目(51335003)资助.

详细信息

作者简介:
袁惠群,教授,主要研究方向:转子动力学.E-mail:yuan_hq@163.com

中图分类号: O326
计量
- 文章访问数: 1036
- HTML全文浏览量: 82
- PDF下载量: 932
- 被引次数: 0
出版历程
- 收稿日期: 2014-03-21
- 修回日期: 2014-05-23
- 刊出日期: 2014-11-18

ANALYTICAL SOLUTION FOR ROTATIONAL RUBBING PLATE UNDER THERMAL SHOCK

1 School of Mechanical Engineering & Automation, Northeastern University, Shenyang 110819, China
2 College of Sciences, Northeastern University, Shenyang 110819, China

Funds: The project was supported by the National Natural Science Foundation of China (51275081) and the State Key Program of National Natural Science of China (51335003).

摘要

摘要: 提出了热冲击和碰摩故障共同作用下的旋转悬臂板系统动力特性解析解法. 基于变分原理,推导出考虑碰摩力沿宽度方向差异性的薄板系统运动微分方程,将该方程的解分解为热冲击悬臂板准静态解和碰摩薄板热冲击动力解. 通过计算旋转悬臂板的模态特性和温度分布函数,获得了碰摩叶片旋转悬臂板模型的热冲击振动解析解,讨论分析得出热冲击和碰摩故障对薄板振动的影响规律. 研究表明:碰摩振动表现为复杂的多频率耦合振动,高频振动较为显著;热冲击振动表现为简单的低频振动形式,强烈的热冲击导致碰摩薄板趋于低频振动. 碰摩引起的振动形式较热冲击故障更加复杂,更容易引起叶片的破坏. 增大的摩擦系数加剧了碰摩引起的振动,利用减小表面粗糙程度等方法降低摩擦系数,可以达到减小碰摩破坏程度的目的.
- 旋转板 /
- 碰摩模型 /
- 热冲击 /
- 变分原理 /
- 解析解
Abstract: The analysis method is developed to obtain dynamic characteristics of the rotating cantilever plate with thermal shock and tip-rub. Based on the variational principle, equations of motion are derived considering the differences between rubbing forces in the width direction of the plate. The transverse deformation is decomposed into quasi static deformation of the cantilever plate with thermal shock and dynamic deformation of the rubbing plate under thermal shock. Then deformations are obtained through the calculation of modal characteristics of rotating cantilever plate and temperature distribution function. Special attention is paid to the influence of tip-rub and thermal shock on the plate. The results show that tip-rub has the characteristics of multiple frequency vibrations, and high frequency vibrations are significant. On the contrary, thermal shock shows the low frequency vibrations. The thermal shock makes the rubbing plate gradually change into low frequency vibrations. Because rub-induced vibrations are more complicated than those caused by thermal shock, tip-rub is easier to result in the destruction of the blade. The increasing friction coefficient intensifies vibrations of the rubbing plate. Minimizing friction coefficients can be an effective way to reduce rub-induced damage through reducing the surface roughness between the blade tip and the inner surface of the casing.
- rotating plate /
- rubbing model /
- thermal shock /
- variational principle /
- theoretical solution

HTML全文

参考文献(25)

Lesaffre N, Sinou JJ, Thouverez F. Contact analysis of a flexible bladed-rotor. European Journal of Mechanics A-solids, 2007, 26(3): 541-557

Batailly A, Legrand M, Cartraud P, et al. Assessment of reduced models for the detection of modal interaction through rotor stator contacts. Journal of Sound and Vibration, 2010, 329(24): 5546-5562

Sinha SK. Non-linear dynamic response of a rotating radial Timoshenko beam with periodic pulse loading at the free-end. International Journal of Non-linear Mechanics, 2005, 40(1), 113-149

Williams RJ. Simulation of blade casing interaction phenomena in gas turbines resulting from heavy tip rubs using an implicit time marching method. In: Proceedings of ASME Turbo Expo, 2011, No. GT2011-45495

刘书国, 洪杰, 陈萌. 航空发动机叶片-机匣碰摩过程的数值模拟. 航空动力学报, 2011, 26(6): 1282-1288 (Liu Shuguo, Hong Jie, Chen Meng. Numerical simulation of the dynamic process of aero-engine blade-to-case rub-impact. Journal of Aerospace Power, 2011, 26(6): 1282-1288 (in Chinese))

Legrand M, Batailly A, Magnain B, et al. Full three-dimensional investigation of structural contact interactions in turbomachines. Journal of Sound and Vibration, 2012, 331(11): 2578-2601

Batailly A, Legrand M, Millecamps A, et al. Numerical-experimental comparison in the simulation of rotor/stator interaction through blade-tip/abradable coating contact. Journal of Engineering for Gas Turbines and Power, 2012, 134(8): 082504

Natarajan S, Baiz PM, Ganapathi M, et al. Linear free flexural vibration of cracked functionally graded plates in thermal environment. Computers and Structures, 2011, 89(15): 1535-1546

Wang BL, Noda N, Han JC, et al. Surface thermal shock fracture of a semi-infinite piezoelectric medium (poling axis parallel to the crack plane). Mechanics of Materials, 2002, 34(3): 135-144

Jeyaraj P, Padmanabhan C, Ganesan N. Vibration and acoustic response of an isotropic plate in a thermal environment. Journal of Vibration and Acoustics-Transactions of the ASME, 2008, 130(5): 051005

Shiau LC, Kuo SY, Liu YP. Aerothermoelastic analysis of composite laminated plates. Composite Structures, 2012, 94(6): 1982-1990 .

熊启林, 田晓耕, 沈亚鹏等. 瞬态热冲击下层合材料板界面的热弹性行为. 力学学报, 2011, 43(3): 630-634 (Xiong Qilin, Tian Xiaogeng, Shen Yapeng, et al. Theromelastic behavior of interface of composite plate under thermal shock. Chinese Journal of Theoretical and Applied Mechanics, 2011, 43(3): 630-634 (in Chinese))

Zhang NH, Wang ML. A mathematical model of thermoviscoelastic FGM thin plates and Ritz approximate solutions. Acta Mechanica, 2006, 181(3): 153-167

Rao GV, Sinha G, Mukherjee N, et al. A finite element free vibration analysis of a thermally stressed spinning plate. Computers & Structures, 1996, 59(2): 377-385

Klauke T, Strehlau U, Kuhhorn A. Integer frequency veering of mistuned blade integrated disks. Journal of Turbomachinery, 2013, 135(6): 061004

Farrahi GH, Tirehdast M, Abad EM, et al. Failure analysis of a gas turbine compressor. Engineering Failure Analysis, 2011, 18(1): 474-484

Gronstedt T, Irannezhad M, Lei X, et al. First and second law analysis of future aircraft engines. Journal of Engineering for Gas Turbines and Power, 2014, 136(3): 031202

徐芝纶. 弹性力学. 第三版. 北京: 高等教育出版社, 1990. 1-4 (Xu Zhilun. Elasticity. 3rd edn. Beijing: Higher Education Press, 1990. 1-4 (in Chinese))

Reddy JN. Energy Principles and Variational Methods in Applied Mechanics. 2nd ed. New York: John Wiley & Sons Inc, 1984

Anthony Guégan. Parameter study of bladed disk/casing interactions through direct contact in aero-engine assemblies. [Dessertation]. Structural Dynamics and Vibration Laboratory, McGill University, 2008

寇海江, 袁惠群, 闻邦椿等. 中心刚体-旋转悬臂板耦合系统碰摩动力特性解析法研究. 固体力学学报, 2013, 34(2): 125-132 (Kou Haijiang, Yuan Huiqun, Wen Bangchun, et al. Study on rubbing dynamic behavior of hub-plate with analytical method. Chinese Journal of Solid Mechanics, 2013, 34(2): 125-132 (in Chinese))

Zhang YX, Wang BL. Thermal shock resistance analysis of a semi-infinite ceramic foam. International Journal of Engineering Science, 2013, 62: 22-30

Yoo HH, Pierre C. Modal characteristic of a rotating rectangular cantilever plate. Journal of Sound and Vibration, 2003, 259: 81-96

王元淳. 板热弯曲问题的一种新解法. 工程力学. 1996, 13(4): 69-73 (Wang Yuanchun. A new solution for thermal bending problem of plates. Engineering Mechanics. 1996, 13(4): 69-73 (in Chinese))

Liu JY, Hong JZ. Geometric nonlinear formulation and discretization method for a rectangular plate undergoing large overall motions. Mechanics Research Communications, 2005, 32(5): 561-571

施引文献

资源附件(0)

访问统计