前体涡发生器对轴对称高超声速进气道激波振荡流动的影响实验

高文智; 李祝飞; 曾亿山; 杨基明

doi:10.6052/0459-1879-17-259

前体涡发生器对轴对称高超声速进气道激波振荡流动的影响实验

1(合肥工业大学机械工程学院,合肥 230009)
2(中国科学技术大学近代力学系,合肥 230027);

详细信息

作者简介:
null

作者简介：2)高文智，讲师，主要研究方向：高超声速空气动力学. E-mail: wzgao@hfut.edu.cn

中图分类号: O355, V231.3;
计量
- 文章访问数: 1929
- HTML全文浏览量: 398
- PDF下载量: 318
出版历程
- 收稿日期: 2017-07-17
- 刊出日期: 2018-03-17

EXPERIMENTAL INVESTIGATIONS OF EFFECTS OF FOREBODY VORTEX GENERATORS ON THE OSCILLATORY FLOW OF AN AXISYMMETRIC HYPERSONIC INLET

1(School of Mechanical Engineering,Hefei University of Technology, Hefei 230009,China)

摘要

摘要: 激波振荡是高超声速进气道不起动过程中常见的流动现象,会显著降低进气道气流捕获与压缩效率、产生剧烈的非定常气动力载荷而危害飞行器安全. 从激波振荡的控制出发,实验研究了前体转捩带位置的涡发生器对轴对称高超声速进气道激波振荡流动的影响. 分别在起动和激波振荡两种进气道流态下,选择无、0.5 mm与1 mm高度涡发生器工况进行对比研究. 并采用高速纹影与壁面动态测压同步记录非定常流动特征. 结果表明,1 mm高度内的涡发生器对起动状态的进气道主流流场结构、壁面压强分布影响不显著. 但对于激波振荡流动,涡发生器会明显缩小外压缩面分离区运动范围,缩短振荡周期,提升振荡周期内壁面压强的时均值. 涡发生器的影响程度随其高度的增大而增强,其中振荡周期从无涡发生器的4 ms缩短到1 mm高度涡发生器的3.13 ms. 此外,0.5 mm高度涡发生器会使得进气道内部测点的压强振荡幅值整体下降,相比无涡发生器工况的下降幅度可达23%. 流场结构与壁面压强信号的分析表明,涡流发生器主要通过其产生的流向涡影响激波振荡流动,包含流向涡对下游边界层的扰动以及流向涡与分离区的相互干扰.
- 激波振荡 /
- 高超声速进气道 /
- 涡发生器 /
- 非定常分离流 /
- 激波风洞
Abstract: Shock oscillations are common flow phenomena encountered in the unstarting processes of hypersonic inlets. They can significantly reduce the airflow capturing and compression efficiency and generate severe unsteady aerodynamic loads. These are highly detrimental to the fight safety of hypersonic vehicles. Aiming at the control of shock oscillation flows, the effects of vortex generators on the oscillatory flows of an axisymmetric hypersonic inlet are studied experimentally. Both started flows and oscillatory flows are investigated with synchronized high speed schlieren imaging and transient surface pressure measurement, as no vortex generators, 0.5 mm and 1 mm thick vortex generators fixed on the inlet forebody. According to the experimental results, minor effects are exerted on the main flowfield and wall pressure of the started flows for vortex generators within 1 mm thickness. However, the vortex generators can substantially reduce the scale of external separations, shorten the oscillatory period and increase the time- averaged pressure magnitude of the oscillatory flows. The effects of vortex generators enhance with the increase of their thickness, and the oscillatory period is shortened from 4 ms for no vortex generator cases to 3.13 ms for 1 mm thick vortex generator cases. In addition, the 0.5 mm thick vortex generators can generally reduce the oscillatory amplitude of surface pressure of the inlet duct, of which decreasing percentage can reach 23%. According to the analysis of the schlieren images and the surface pressure signals, effects of the vortex generators are exerted through streamwise vortexes in the wake flows, including the disturbances of streamwise vortexes exerted on the downstream boundary layers and the interactions between streamwise vortexes and separation regions.
- shock oscillation /
- hypersonic inlet /
- vortex generator /
- unsteady separated flow /
- shock tunnel

HTML全文

参考文献(1)

[1]	Van Wie DM.Scramjet inlets. Scramjet Propulsion, 2000, 189: 447-511
[2]	Van Wie DM, Kwok FT, Walsh RF. Starting characteristics of supersonic inlets. AIAA Paper, 1996-2914, 1996
[3]	Voland RT, Auslender AH, Smart MK. CIAM/NASA Mach 6.5 scramjet flight and ground Test. AIAA Paper, 1999-4848, 1999
[4]	Rozenberg Z.Second X-51 hypersonic flight ends prematurely. Flight International. Flightglobal. 15 June 2011 , Second X-51 hypersonic flight ends prematurely. Flight International. Flightglobal. 15 June 2011,
[5]	Tan HJ, Sun S, Yin ZL.Oscillatory flows of rectangular hypersonic inlet unstart caused by downstream mass-flow choking. Journal of Propulsion and Power, 2009, 25(1): 138-147
[6]	Li ZF, Gao WZ, Jiang HL, Yang JM.Unsteady behaviors of a hypersonic inlet caused by throttling in shock tunnel. AIAA Journal, 2013, 51(10): 2485-2492
[7]	Wagner JL, Valdivia A, Clemens NT, et al.Experimental investigation of unstart in an inlet/isolator model in Mach 5 flow. AIAA Journal, 2009, 47(6): 1528-1542
[8]	Tan HJ, Li LG, Wen YF, et al.Experimental investigation of the unstart process of a generic hypersonic inlet. AIAA Journal, 2011, 49(2): 279-288
[9]	Trapier S, Deck S, Duveau P.Delayed detached-eddy simulation and analysis of supersonic inlet buzz. AIAA Journal, 2008, 46(1): 118-131
[10]	Hong W, Kim C.Computational study on hysteretic inlet buzz characteristics under varying mass flow conditions. AIAA Journal, 2014, 52(7): 1351-1373
[11]	Do H, Im S, Mungal MG, et al.The influence of boundary layers on supersonic inlet flow unstart induced by mass injection. Exp Fluids, 2011, 51(3): 679-691
[12]	Im S, Baccarella D, McGann B, et al. Unstart phenomena induced by mass addition and heat release in a model scramjet. Journal of Fluid Mechanics, 2016, 797: 604-629
[13]	Huang HX, Tan HJ, Sun S, et al.Behavior of shock train in curved isolators with complex background waves. AIAA Journal, Published online. DOI: 10.2514/1.J056166(check)
[14]	Zhang QF, Tan HJ, Sun S, et al.Unstart of a hypersonic inlet with side compression caused by downstream choking. AIAA Journal, 2016, 54(1): 28-38
[15]	Chang JL, Wang L, Bao W, et al.Novel oscillatory patterns of hypersonic inlet buzz. Journal of Propulsion and Power, 2012, 28(6): 1214-1221
[16]	Wagner JL, Yuceil KB, Clemens NT.Velocimetry measurements of unstart in an inlet-isolator model in Mach 5 flow. AIAA Journal, 2010, 48(9): 1875-1888
[17]	Valdivia A, Yuceil KB, Wagner JL, et al.Control of supersonic inlet-isolator unstart using active and passive vortex generators. AIAA Journal, 2014, 52(6): 1207-1218
[18]	Im S, Do H, Cappelli MA.The manipulation of an unstarting supersonic flow by plasma actuator. J Phys D: Appl Phys, 2012, 45(48): 485-502
[19]	Lu FK, Li Q, Liu CQ.Microvortex generators in high-speed flow. Progress in Aerospace Sciences, 2012, 53: 30-45
[20]	童福林,李新亮,唐志共. 激波与转捩边界层干扰非定常特性数值分析. 力学学报, 2017, 49(1): 93-104
[20]	(Tong Fulin, Li Xinliang, Tang Zhigong.Numerical analysis of unsteady motion in shock wave/transitional boundary layer interaction. Chinese Journal of Theoretical and Applied Mechanics, 2017, 49(1): 93-104 (in Chinese))
[21]	Berry S, Daryabeigi K, Wurster K.Boundary-layer transition on X-43A. Journal of Spacecraft and Rockets, 2010, 47(6): 922-934
[22]	Schneider S.Effects of roughness on hypersonic boundary-layer transition. Journal of Spacecraft and Rockets, 2008, 45(2): 193-209
[23]	宋威, 蒋增辉, 贾区耀. 细长锥边界层绊线转捩风洞自由飞试验. 力学学报, 2016, 48(6): 1301-1307
[23]	(Song Wei, Jiang Zenghui, Jia Quyao.Wind-tunnel free-flight test of boundary layer transition induced by tripped thread for slender cone. Chinese Journal of Theoretical and Applied Mechanics, 2016, 48(6): 1301-1307 (in Chinese))
[24]	Williams OJH, Smits AJ.Effect of tripping on hypersonic turbulent boundary-layer statistics. AIAA Journal, 2017, 55(9): 3051-3058
[25]	朱德华,袁湘江,沈清等. 高超声速粗糙元诱导转捩的数值模拟及机理分析. 力学学报, 2015, 47(3): 381-388
[25]	(Zhu Dehua, Yuan Xiangjiang, Shen Qing, et al.Numerical simulation and mechanism analysis of hypersonic roughness induced transition. Chinese Journal of Theoretical and Applied Mechanics, 2015, 47(3): 381-388 (in Chinese))
[26]	高文智,李祝飞,杨基明. 一种鼻锥钝化高超声速轴对称进气道流动特性实验. 航空学报,2015, 36(1): 302-310
[26]	(Gao Wenzhi, Li Zhufei, Yang Jiming.Flow characteristics experiments of a hypersonic axisymmetric inlet with nose bluntness.Acta Aeronautica et Astronautic Sinica, 2015, 36(1): 302-310 (in Chinese))
[27]	Fan XQ, Li H, Jia D, et al.Experimental investigation on forced boundary-layer transition of axisymmetric inlet and numerical verification. Journal of Aircraft, 2006, 43(5): 1544-1549
[28]	Eagle WE, Driscoll JF.Shock wave-boundary layer interactions in rectangular inlets: three-dimensional separation topology and critical points. Journal of Fluid Mechanics, 2014, 756: 328-353
[29]	Panaras AG.Review of the physics of swept-shock/boundary layer interactions. Progress in Aerospace Sciences, 1996, 32(2): 173-244
[30]	高文智, 李祝飞, 杨基明等. 一种用于前缘钝化高超声速进气道设计评估的 CFD/特征线组合方法及其应用. 推进技术, 2013, 34(12): 1585-1592
[30]	(Gao Wenzhi, Li Zhufei, Yang Jiming, et al.A combined CFD/characteristic method for design and performance prediciton of hypersonic inlet with leading edge bluntness. Journal of Propulsion Technology, 2013, 34(12): 1585-1592 (in Chinese))
[31]	Gao WZ, Li ZF, Yang JM.A hybrid CFD/characteristics method for fast characterization of hypersonic blunt forebody/inlet flow. Science China G: Physics, Astronomy & Mechanics, 2015, 58(10): 38-45
[32]	李祝飞, 高文智, 李鹏等. 二元高超声速进气道激波振荡特性实验. 推进技术, 2012, 33(5): 676-682
[32]	(Li Zhufei, Gao Wenzhi, Li Peng, et al.Experimental investigation on the shock wave oscillation behaviors in a two-dimensional hypersonic inlet flow. Journal of Propulsion Technology, 2012, 33(5): 676-682 (in Chinese))
[33]	Srikant S, Wagner JL, Valdivia A, et al.Unstart detection in a simplified-geometry hypersonic inlet-isolator flow. Journal of Propulsion and Power, 2010, 26(5): 1059-1071

施引文献(5)

期刊类型引用(3)

1.	王德鑫，褚佑彪，刘难生，李祝飞，杨基明. 高背压进气道中内外流耦合作用的大涡模拟. 航空学报. 2021(09): 270-283 . 百度学术
2.	王殿恺，文明，王伟东，卿泽旭. 脉冲激光与正激波相互作用过程和减阻机理的实验研究. 力学学报. 2018(06): 1337-1345 . 本站查看
3.	高文智，曹绕，李祝飞，曾亿山，杨基明. 涡发生器对高超声速轴对称进气道外部流动的影响. 气体物理. 2018(06): 51-62 . 百度学术